Make Your Own Hats
r any velvet eighteen to twenty-four inches wide. If velvet
over
angles to brim to avoid marring the velvet. Pin closely all around edge of brim, pulling material with the thread to remove any fullness. Do not pull tight enough to bend the brim. Trim velvet
lvet edge
e to stitch the buckram in from the edge about one-fourth inch with the sewing machine, using a long stitch. This stitching may then be used to put the needle through when sewing the vel
OF FITTING FABR
nder side
before beginning to sew. Place pins in at right angles to brim. A piece of velvet held in the left hand will prevent finger marks from showing on the velvet. Begin to sew at left of wire joining, while holding underside of brim towards you. Bring needle through from back close under wire. With the head of the needle press velvet along under wire to make a crease or sort of bed for the thread of the next stitch. Take nearly a half-inch stitch by placing needle close under the wire and coming through
F BRIM PINNED OVER WIR
er cro
round. Gather one-fourth inch from edge, place over top, equalize the gathers, pin in place, and sew with stab sti
er sid
d side crown to find length and to locate seam. Draw it snugly and pin seam on straight of material with warp thread. (Warp
crown o
brim and crown one-fourth inch from bottom wire. Stretch the velvet strip for side crown on the crown, placing seam at back, unless trimming has been planned which will cover the seam better if it is plac
ing, when finish
the needle through from underside of facing to the very edge of fold. Place point of needle directly opposite this stitch and take a small stitch in upper facing, then take a small stitch in underfacing. Each stitch always begins just opposite the ending of precedin
brim sailor with
s to mark the line that must be placed on the edge of the brim. If the velvet is not placed evenly, there will be found a greater amount of fullness on one side than on the other. Place velvet over the brim and pin on edge at points marked by pins. Stretch as tight as possible. On a brim of this width all of the fullness should be worked out. If this is found to be very difficult, lay the brim aside, with the velvet pinned on, for an
ci
only from headsize wire to within an inch of the edge of the brim. In this case there could be a strip of material the same as upper facing an inc
with two kin
same time have much charm. For instance, the edge of the hat could have a bias band of satin, two or more inches wide, stretched around the edge of the brim, with the rest of the brim covered with velvet overla
brim fo
aped brim is th
pattern
d width. To make the brim droop, slash the pattern from the edge to the headsize wire in four different places equally distant. Lap these slashes one-fourth inch at the edge, and pin.
tside edge and allow one-fourth inch for the lap at ends. Mark on buckram with pencil close to headsize line and cut one-half inch inside this mark. Lap ends one-fourth inch and backstitch closely at each edge of flap. Sew a strip of crinoline flat over seam to smoo
mushroom-
losely at edge, with pins at right angles to the brim. If covered with georgette, satin or silk, which is pliable, the fullness may all be worked out without a seam. Baste close to headsize wire and finish edge by following same method as used in finishing sa
mate
erial first. The color could be made deeper by using a lining of the same color, or made pal
with rolled or c
ttern can be adjusted to any desired shape. It is an advantage sometimes to cut the paper pattern through in the back, leaving pins in the slashes, and lay out flat on another piece of paper for a new pattern. This eliminates some of the slashes and makes further experiments easier. Pattern-making is very important, and it is of extreme value to make as many patterns as possible before
ose-fitting o
the left and pin at the edge; also at the headsize wire. Then proceed in the same way toward the right, always pinning closely. Be sure to keep the material tight and smooth both at edge and at the headsize wire. Allow the fullness to go whe
pstitc
e other side, always being careful to begin the stitch exactly opposite the end of the one preceding. Try to cut the material out from inside the headsize wire in one piece so that it may be used for something else. Examine the material carefully to make sure that it fits perfectly. Baste
elvet to
the brim, so we resort to milliner's glue. Do not use glue on satin, or on any fabric thinner than velvet, or on any frame ot
further. Be very careful to keep the glue away from the right side of the velvet. Next, rub the glue on the frame with a stiff brush until it is smooth, then spread the velvet back into place, pressing and smoothing it with the hands from the headsize wire out. Watch it carefully for any places which have not sufficient glue, as
headsize wire. Keep the material smooth; work from right to left, and then from left to right. Work the material around to where the seam is to be made. Cut away all superfluous materia
d crown
et is especially beautiful made up in this way. The first method is the preferred. Cut a circular piece of material, havi
marked a circle in the center about three inches in diameter. Gather on the line of each circle wi
ade at the center of the crown top and sewed securely in place. The material should be pinned down at four equal points at the edge of the crown, the threads of the other circles pulled up
ngthwise thread of the material. The first shirring or gathering should be one-half inch from the edge, the additional threads should be run in evenly every half inch. The first thread near the edge should then be drawn up as tightly as possible and this edge pushed through the hole in
Billionaires
Romance
Romance
Billionaires
Romance
Romance